Skip to content

Legal Description of Property: How to Read One

Al de PalmaAl de Palma
November 14, 20269 min read
Survey map with section lines and a drafting compass on a wooden table
Survey map with section lines and a drafting compass on a wooden table

The legal description of property is the part of a deed that says exactly which piece of land is being sold. It is not the street address. Vacant land often has no address at all, and an address can change. The legal description is what the county records, what title companies insure and what a surveyor stakes on the ground.

In the United States you will meet three kinds: lot and block, township, range and section, and metes and bounds. This guide shows how to read each one, with worked examples, and what to check before you buy.

Key Takeaways

  • A legal description identifies a parcel precisely enough that it could not be confused with any other. The street address and the parcel number do not do that on their own.
  • Lot and block descriptions point to a recorded subdivision plat. Most small lots in Florida and Mississippi subdivisions are described this way.
  • Township, range and section descriptions use the federal survey grid. Read them backwards, from the largest unit to the smallest.
  • A standard section is nominally one square mile, or 640 acres, so each quarter is nominally 160 acres.
  • Metes and bounds descriptions walk the boundary from a point of beginning using bearings and distances, and must close back on the start.
  • Before buying, check that the legal description on the deed matches the plat, the county parcel record and the land you were shown.

Table of Contents

What a legal description of property is

A legal description is a written description of a parcel's boundaries that is precise enough for a surveyor to locate it without any other information. It appears on the deed, the title commitment, the mortgage or financing documents and the recorded plat or survey.

Three other identifiers are easy to mistake for it:

IdentifierWhat it isWhy it is not enough
Street addressA mailing location assigned by the county or cityVacant land often has none, and addresses can be reassigned.
Parcel number (APN)The tax assessor's ID for the parcelIt exists for tax billing and can change when parcels are split or combined.
GPS pin or map polygonA point or outline on a mapUseful for orientation, but county GIS maps are approximate and not a survey.
Legal descriptionThe recorded definition of the boundaryThis is the one that controls.

Lot and block: the plat description

When land is subdivided, the developer records a plat: a map of the subdivision showing every lot, block, street and easement, with dimensions. After that, each lot can be described simply by pointing to the plat. A typical description looks like this (the names and numbers here are made up):

"Lot 12, Block 34, of Example Shores Unit 2, according to the plat thereof recorded in Plat Book 5, Page 67, of the Public Records of Example County, Florida."

To read it, find the plat. The county clerk or recorder keeps plat books, and most counties now let you search and view them online. Open Plat Book 5, Page 67, find Block 34 and then Lot 12. The plat shows the lot's dimensions, its frontage on the street and any easements across it, such as utility or drainage strips along the back line.

Lot and block is the simplest kind of description, and it is how most small lots in older Florida and Mississippi subdivisions are described. It is still worth opening the plat yourself. Plats show things a listing photo cannot, like a drainage easement that takes the back 10 feet of a lot, or a "street" that was drawn on paper but never built.

Township, range and section

Outside of platted subdivisions, much of the country is described using the Public Land Survey System (PLSS), created by the Land Ordinance of 1785 to survey and sell federal land. It covers 30 states, including Florida and Mississippi. It lays a grid over the land, measured from a north-south line (a principal meridian) and an east-west line (a baseline).

  • Township numbers count 6-mile rows north or south of the baseline.
  • Range numbers count 6-mile columns east or west of the meridian.
  • Where a township row and a range column cross, you get a square called a township, nominally 6 miles on each side, or 36 square miles.
  • Each township is divided into 36 sections of nominally 1 square mile, or 640 acres. Section 1 is in the northeast corner, and the numbers snake back and forth, ending with Section 36 in the southeast corner.
  • Sections are then split into halves and quarters, called aliquot parts.

"Nominally" matters: because the earth is curved and old surveys were imperfect, some sections, especially along the north and west edges of a township, are larger or smaller than 640 acres. The deed's stated acreage, or a survey, is what counts for a specific parcel.

How to read it: right to left

Take this example:

"The North 1/2 of the Southwest 1/4 of the Southeast 1/4 of Section 22, Township 10 South, Range 24 East."

Read it from the end, starting with the largest area:

  1. Township 10 South, Range 24 East. The tenth row south of the baseline and the twenty-fourth column east of the meridian. That is one 36-square-mile township.
  2. Section 22. One square mile inside that township: nominally 640 acres.
  3. Southeast 1/4. The southeast quarter of Section 22: 640 ÷ 4 = 160 acres.
  4. Southwest 1/4. The southwest quarter of that quarter: 160 ÷ 4 = 40 acres.
  5. North 1/2. The north half of that 40: 40 ÷ 2 = 20 acres.
StepAreaNominal size
Section 22Whole section640 acres
SE 1/4Quarter section160 acres
SW 1/4 of the SE 1/4Quarter-quarter (a "forty")40 acres
N 1/2 of the SW 1/4 of the SE 1/4Half of a forty20 acres

Real descriptions often mix systems. A common pattern is an aliquot part followed by "less and except" language that carves out a road right of way or a piece sold earlier. Read every exception: they tell you what you are not getting.

Metes and bounds

Metes and bounds describes land by walking its boundary. It is the oldest system in the U.S., used in the original colonies and in states that were never part of the PLSS, and it is still used everywhere for irregular parcels or pieces cut out of larger tracts. "Metes" are the measurements (directions and distances); "bounds" are the boundaries and markers.

A metes and bounds description has three parts:

  1. A point of beginning (POB). A fixed starting point, usually tied to a section corner, a recorded monument or an iron pin. For example: "Commence at the southeast corner of Section 22… thence west 330 feet to the Point of Beginning."
  2. Calls. A series of bearings and distances, each starting with "thence": "thence North 14°32' East, 412.80 feet; thence South 75°28' East, 210.00 feet…" A bearing is an angle measured east or west from north or south.
  3. Closure. The last call must return to the point of beginning. If it does not, the description has an error and the boundary is uncertain.

You can check closure yourself with free plotting tools that draw a parcel from its calls. A shape that does not close, or that looks nothing like the parcel on the county map, is a reason to stop and order a survey.

Legal descriptions in Florida and Mississippi

Both states are PLSS states, so rural parcels are tied to townships, ranges and sections. Florida's survey is measured from the Tallahassee meridian and baseline. Mississippi has several meridians, so its descriptions sometimes name which one applies.

In practice, most small residential lots in both states are in recorded subdivisions and use lot and block descriptions. Many of these subdivisions were platted decades ago with thousands of small lots, and some of the streets on the plat were never built. When you look at a lot in an older subdivision, check three things on the plat and the county map: that the street in front of the lot actually exists and is maintained, what easements cross the lot, and whether the lot is being sold on its own or as part of a combined parcel.

Street access is a topic of its own; see our guide to vacant land due diligence for how to confirm road frontage before you buy.

How to find and check a legal description

  1. Get the current deed. Search the county recorder or clerk's official records by owner name or parcel number. The legal description is in the body of the deed.
  2. Compare it with the assessor's record. The property appraiser or tax assessor shows a short legal description and the parcel number. The two should describe the same land. Assessor descriptions are often abbreviated, so the deed controls.
  3. Open the plat or plot the calls. For lot and block, view the plat. For metes and bounds, plot the calls and check that they close.
  4. Match it to the ground. Compare with the county GIS map and, if you visit, look for corner pins. If anything does not line up, a licensed surveyor can locate and stake the boundary.
  5. Read the title commitment. When you buy through a title company, the commitment repeats the legal description and lists exceptions such as easements and restrictions. That is the description your title policy will insure.

Frequently asked questions

It is the written description of a parcel's boundaries that appears on the deed and other recorded documents. It identifies the land precisely enough that a surveyor could locate it without any other information. In the U.S. it usually takes one of three forms: lot and block, township, range and section, or metes and bounds.

Look at your deed, which you can get from the county recorder or clerk's official records by searching your name or parcel number. The county property appraiser or assessor also shows a short version, and a title commitment or survey repeats it. If the sources differ, the recorded deed is the one that controls.

How do you read township, range and section?

Read it backwards. Start with the township and range to find the 36-square-mile township, then the section number to find the one-square-mile section, then work left through each fraction. The north half of the southwest quarter of the southeast quarter of a section is nominally 20 acres.

What does metes and bounds mean?

Metes and bounds describes a parcel by walking its boundary. It starts at a fixed point of beginning and lists each side as a direction, called a bearing, and a distance, until it returns to the start. Metes are the measurements; bounds are the boundaries and markers along the way.

No. The parcel number, or APN, is an ID the tax assessor uses for billing. It points to a record that includes a short legal description, but the number itself does not define the boundary, and it can change when parcels are split or combined.

Do I need a survey when buying vacant land?

Not always. For a lot in a recorded subdivision with visible corner pins, the plat may be enough. A survey is worth it when the description is metes and bounds, when corners are missing, when you plan to build close to a line or when anything on the plat, deed and county map does not match.

See the parcel before you commit

Every LOTSS$ listing shows the parcel number, county and map location, so you can pull the deed and the plat from the county records before you buy. Select Florida lots are also available with owner financing: 20% down and up to 36 months for the balance.

Browse available lots

This article is general information, not legal or surveying advice. For a boundary question on a specific parcel, consult a licensed surveyor or real estate attorney.